Rail is not one noise source. Two trains of identical length produce entirely different spectra depending on whether they are running at 300 km/h on a high-speed line, crawling through a station, or hauling freight at night — and an elevated metro line radiates from its structure as well as its track. A barrier specified for one of these is rarely correct for another.
This page is the entry point for the rail and transit section types. The detail pages cover each one; what follows is the reasoning that connects them.
| Situation | Dominant source | What sets the barrier |
|---|---|---|
| High speed line | Rolling and aerodynamic noise | Height above the train, aerodynamic load |
| Intercity mixed traffic | Night freight, plus fast passenger | The tallest vehicle in the mix |
| Freight corridor | Low speed, heavy axle loads, low frequency | Wagon height and night criterion |
| Metro viaduct | Track noise plus deck re-radiation | Structural allowance, soffit radiation |
| Light rail | Rolling, curve squeal, traction | Available space in a street |
| Station and platform | Braking, idling, plant | Circulation, sightlines, access |
| Tunnel portal | Concentrated emission from one opening | Height of the opening, and lining inside |
Rolling noise rises and shifts upward in frequency as speed increases. That single relationship explains most of the differences between rail cases:
At high speed, energy concentrates in the mid and high bands, which a barrier attenuates well. Height and continuity matter most.
At low speed with heavy vehicles, energy concentrates in the low bands, which diffracts over and around a barrier readily. Mass and proximity to the source matter more than height.
At a standstill, rolling noise disappears and the residual is dominated by auxiliaries, doors and plant — sources a track-side barrier does not address.
A barrier tuned for the daytime express on a mixed line may under-perform against the night freight that generates the complaint. The design case has to be named explicitly.
On an elevated alignment the deck radiates sound as well as the track, because vibration enters the concrete and is re-radiated from large surfaces underneath. This is the difference between a metro viaduct and the same track at grade, and it is the reason a parapet screen can be installed at considerable cost for a modest measured change where soffit radiation dominates.
The practical consequence is a sequence: establish whether the receiver is beside the structure or below it, then decide whether the dominant path is airborne from the track or radiated from the deck. Only the first is a barrier problem.
| Constraint | Effect on the design |
|---|---|
| Possession windows | Panel system must suit rapid erection in a few hours |
| No plant access along the track | Panel weight limited to manual or small-plant handling |
| Overhead line equipment | Limits proximity and height; restricts lifting |
| Structure gauge | Barrier cannot encroach on the vehicle envelope |
| Buried services and signalling | Foundation positions constrained along the whole run |
| Driver sightlines | Height and continuity limited at curves and signals |
On a live railway, a barrier that is efficient to manufacture but slow to erect is the wrong barrier, whatever its acoustic performance. The design should be judged on what can be built in the time available.
Being direct about this saves projects money:
Curve squeal in a street-running tramway — a wheel-rail interface problem, addressed by friction management, not screening.
Deck re-radiation from a viaduct soffit — a structure-borne path that a parapet screen does not touch.
Station platform activity — doors, announcements and crowds are distributed sources that resist screening.
Ground-borne vibration — passes through the ground beneath any barrier; needs track or building measures.
Main line
High speed rail noise barriers — the high-speed case, where aerodynamic and rolling noise both matter.
Intercity railway noise barriers — mixed traffic, where night freight usually sets the design case.
Freight line noise barriers — low speed, high mass, low frequency and nocturnal operation.
Railway station noise barriers — platforms, plant and the building acting as its own barrier.
Urban transit
Metro viaduct noise barriers — deck radiated noise and the structural limits on parapet screens.
Metro and stabling depot noise — depots and yards, often the best barrier opportunity on a transit system.
Light rail noise barriers — street running, curve squeal and the space constraint.
Tunnel
Tunnel portal noise — hoods, portal barriers and absorptive lining, which are three different measures.
Wind load and post spacing — the structural case behind every panel and post choice.
Panel specifications — mass, Rw, absorption and finish, and why one figure is not enough.
Installation sequence — setting out, foundations and base sealing, adapted to possession working.
Maintenance and inspection — what degrades fastest beside a live railway.
Perforated metal absorptive faces — relevant where reflections from a barrier or a tunnel face matter.
Road engineering noise barriers — cuttings, embankments, retaining walls, bridges, interchanges and plazas.
Barrier structure and panel selection — heights, construction types, materials and finishes.
Line type and alignment: at grade, viaduct, cutting or tunnel, with lengths.
Traffic: train types, speeds, axle loads, vehicle heights, and the night timetable.
Which service generates the complaint, and when.
Track form and condition, including known corrugation or joint locations.
Nearest dwellings and their height relative to rail level.
Constraints: OLE, structure gauge, sightlines, buried services, possession arrangements.
Item three is the one most often omitted, and it decides which detail page applies.
Related reading: road engineering noise barriers, structure and panel selection, and HSR noise barrier range.
Because the constraints differ more than the acoustics. Railway barriers face driver sightlines, overhead line equipment, structure gauge, possession windows and buried signalling, none of which apply to a road verge. The structural load case is also repeated many times a day rather than occasional.
Street-running light rail, because there is no corridor to put a barrier in — the track shares the street with footways, crossings and stops. Elevated metro is second, because the deck itself radiates sound in a way a parapet screen cannot address.
No. Height is limited by sightlines, OLE and structure gauge, and on an elevated alignment extra height does nothing for deck radiated noise. Where the receiver is below a viaduct, track treatment often delivers more than any parapet screen.
Not directly. High-speed noise is dominated by mid and high frequencies that a barrier attenuates well; freight concentrates energy at low frequency, where barriers are weakest, and the wagons are taller so more height is needed for the same result.
Track and wheel treatment — grinding, removing joints, rail damping and wheel maintenance. It reduces the source for every receiver along the corridor, including the low-frequency components a barrier handles poorly, and it is often cheaper per decibel.
Contact Us
Imfornation
29 STC Noise Barrier WholesaleNoise Barrier Wind Load: Posts, Spacing and FoundationsMining and Quarry Noise Barriers: Dust, Plant and LayoutWind Farm Noise: What a Barrier Can and Cannot DoChain Link Fence: Wire, Mesh and Coating SelectionMetro Viaduct Noise Barrier: Deck Radiated NoisePoultry Farm Noise: Ventilation Fans and GeneratorsTemporary Fence: Panels, Ballast and Wind Load on SiteConstruction Hoarding Panels: Wind Load and Site BoundariesSchool Noise Barrier: Cutting Traffic Noise at the ClassroomGabion Basket SupplierAnti-Climb Fence Specification: 358 Mesh, Paladin Pales and 3D PanelsTemporary Noise Barrier: Rent or Buy, and What Drives CostNoise Barrier Panel Specifications: The Six NumbersCar Park Noise: Ventilation, Ramps and Rooftop PlantConstruction Site Fencing: Temporary Panels, Welded Mesh or HoardingResidential Noise Barrier: Height, Planning and Appearance0.85 NRC Noise Barrier Wholesale111Gabion Baskets for saleWarehouse Noise Barrier: Docks, Plant and YardsGabion Retaining Wall: Sizing, Drainage and Stone FillGenerator Noise Barrier: Tonal Noise and Airflow3m High Noise Barrier5m High Noise BarrierWastewater Plant Noise: Blowers and Continuous PlantHospital Noise Barrier: Ward Targets, Height and CleanabilityLaboratory Noise: Fume Hoods, Compressors and VibrationNoise Control SolutionsNoise Barrier Guide: Types, Height, Cost and SelectionInfrastructure Noise ControlRail and Transit Noise Barrier: Lines, Stations, DepotsAluminum Alloy Noise Barrier SupplierTunnel Portal Noise: Hoods, Barriers and AbsorptionHighway Interchange Noise Barrier: Multi Level LayoutRailway Station Noise: Platforms, Plant and ApproachesPlace of Worship Noise Barrier: Chimes, PA and Plant2m High Noise BarrierCutting and Embankment Noise Barrier: Section GeometryPerforated Metal Noise Barrier: Open Area and AbsorptionRoad Engineering Noise Barrier: Sections and StructuresFreight Railway Noise Barrier: Low Speed, High MassData Centre Cooling Noise: Louvre Screens and AirflowShopping Centre Noise: Rooftop Plant and DeliveriesAir Source Heat Pump Noise Barrier: Screens and Airflow