hotproduct

Noise Barrier Panel Specifications: The Six Numbers

Two noise barrier quotes can look identical on the page and describe completely different products. The difference is almost never the price per square metre — it is which six numbers each supplier chose to publish. A specification that omits mass per square metre and quotes only a decibel figure is not a specification, it is a claim.

What a panel specification has to state

PropertyUnitWhy it decides the outcome
Mass per unit areakg/m²The single number that governs low-frequency performance
Panel thicknessmmSets the depth of the absorber cavity and the fixing geometry
Sound reduction indexRw or Dw, dBLaboratory or field rating of the panel alone or in a system
Absorption coefficientNRC or αwDetermines whether the panel absorbs or reflects on the source side
Skin and finishgauge, coating, µmCorrosion life, and the number that separates two similar-looking panels
Fire performanceclassNon-negotiable on tunnels, stations and enclosed structures

If a datasheet gives only Rw, you cannot tell whether the panel will work at 100 Hz. If it gives only mass, you cannot tell whether it will reflect sound back at the road. Both are needed, and they are not interchangeable.

Mass per square metre is the master number

The mass law is the reason. Doubling the mass per unit area buys roughly 5–6 dB of reduction, and the benefit is largest at low frequency. That is why a 20 kg/m² panel and a 10 kg/m² panel of identical construction are not variants of the same product — they are different products with a 5 dB gap that no amount of careful installation will close.

This is also why a lightweight panel with a good mid-frequency rating can disappoint on a highway. Traffic noise carries substantial energy below 250 Hz, where light panels are weakest. The number that predicts field performance at that frequency is mass, not the headline Rw.

Absorption and insulation are different jobs


Insulation (Rw, Dw)Absorption (NRC, αw)
What it doesStops sound passing throughStops sound reflecting back
Governed byMass and sealingOpen surface, cavity depth, infill
Where it mattersBetween source and receiverOn the source side, and inside enclosures
Typical formSolid or cassette panelPerforated or louvred face with absorber behind

A barrier beside a road usually wants both: absorptive on the traffic face to stop reflections reaching the far side, and sufficient mass to block transmission. A panel that does one and not the other is half a panel.

Panel construction: what the mass is made of

  • Single skin — one metal sheet. Light, cheap, and the weakest option at low frequency. Adequate for low screens and short runs.

  • Double skin cassette — two sheets with an infill between. The mainstream product: mass where it is needed, and a cavity that can be filled with absorber.

  • Absorptive cassette — perforated or louvred face, mineral wool or similar behind a protective membrane, solid back. Higher NRC, and the correct choice on the source face.

  • Transparent infill — acrylic or polycarbonate set into a frame. Used where daylight or sightlines must be kept; heavier than it looks, and needs its own fixing detail.

Comparing two quotes that look the same

  1. Ask for mass per square metre of the finished panel, not of the steel. Infill, frame and fixings all count.

  2. Ask whether the Rw figure is for the panel alone or for a mounted system. A panel tested in a laboratory wall is not the same as a panel on posts with a gap at the base.

  3. Ask for the absorption figure separately. A single combined number hides which face does what.

  4. Ask for coating thickness in microns and the substrate. Two galvanised panels at 20 µm and 60 µm have very different lives.

  5. Ask what the base detail is. A 3 dB leak at the bottom edge undoes a great deal of panel specification.

Where specifications usually go wrong

  • A decibel figure is quoted without a frequency, which makes it unfalsifiable.

  • Mass is stated for the steel skin but the panel is a cassette with a light infill, so the real figure is lower.

  • A laboratory Rw is presented as the field performance, ignoring posts, gaps and diffraction over the top.

  • Transparent panels are substituted for metal ones on a frame designed for the lighter panel.

  • Fire class is left unstated on a station or tunnel project where it is the first question the engineer asks.

What to send for a panel recommendation

  1. Required reduction at the receiver, and the frequency band that matters if it is known.

  2. Barrier height and total run length.

  3. Whether the source face should absorb or reflect.

  4. Any transparency requirement, and how much of the panel area it covers.

  5. Exposure: coastal, industrial, de-icing salt.

  6. Fire performance class required by the project.

Items one and three decide the panel; the rest decide the finish and the frame.

Related reading: acoustic noise barrier range, 4 m noise barrier panel, and noise barrier cost per square metre.

Noise Barrier Panel Specifications: The Six Numbers

Frequently asked questions

What mass per square metre should a noise barrier panel have?

It follows from the reduction required and the frequency band. As a working reference, light single-skin panels sit near 10 kg/m² and heavier cassettes above 20 kg/m², with the higher figure appropriate where low-frequency traffic or plant noise dominates. The number should come from the acoustic case, not from a catalogue default.

Is a higher Rw always better?

Not on its own. Rw is a single-figure rating weighted toward speech frequencies, so a panel can score well and still be weak at 125 Hz. For traffic and machinery noise, ask for the octave-band figures and check the low bands rather than relying on the single number.

Can I use a lighter panel if I make the barrier taller?

Only up to the point where the barrier breaks the line of sight. Beyond that, extra height buys very little and does not compensate for insufficient mass. Height and mass solve different parts of the problem.

Do transparent panels have the same performance as metal ones?

They are heavier and more brittle, with different fixing requirements, and their acoustic behaviour differs at low frequency. They are a legitimate choice for sightlines and daylight, but they are not a drop-in substitution into a frame designed for a metal cassette.

How is fire performance specified?

By class, and on tunnels, stations and enclosed structures it is usually the first item the engineer checks. Mineral wool infill and metal skins generally meet the higher classes; some transparent infills and some foam cores do not. State the required class before the panel is selected.

Contact Us

Imfornation

Mining and Quarry Noise Barriers: Dust, Plant and LayoutCooling Tower Noise Barrier: Layout, Airflow and Panel DesignAirport Noise Barrier: Ground Noise, Run-Up and Plant29 STC Noise Barrier WholesaleData Centre Cooling Noise: Louvre Screens and AirflowSolar Noise Barrier Cost: What Drives the Price and the PaybackSubstation and Transformer Noise Barriers: Controlling Low-Frequency HumAnti-Climb Fence Specification: 358 Mesh, Paladin Pales and 3D PanelsGabion Retaining Wall: Sizing, Drainage and Stone FillPerforated Metal Noise Barrier: Open Area and AbsorptionIndustrial Plant Noise Barrier: Boundary Wall and Equipment Enclosure358 Security Fence: Mesh, Wire and Anti-Climb Specification0.85 NRC Noise Barrier WholesaleTemporary Fence: Panels, Ballast and Wind Load on SiteNoise Barrier Guide: Types, Height, Cost and SelectionChain Link Fence: Wire, Mesh and Coating SelectionNoise Barrier Panel Specifications: The Six Numbers1Hospital Noise Barrier: Ward Targets, Height and Cleanability5m High Noise BarrierConstruction Site Noise Barriers: Temporary Screens That Move With the WorksGabion Baskets for saleIndustrial Noise Barrier SystemMetro Depot Noise Barrier: Enclosure for Depots and Over-Track DevelopmentNoise barriers cost3D-Welded Mesh fencing systemNoise Barrier Wind Load: Posts, Spacing and FoundationsInfrastructure Noise Control3m High Noise BarrierResidential Noise Barrier: Height, Planning and AppearanceUrban Noise ControlTemporary Noise Barrier: Rent or Buy, and What Drives CostSchool Noise Barrier: Cutting Traffic Noise at the ClassroomDouble Wire Fence: 868 and 656 Panels, Posts and FixingsHighway Noise Barrier Cost: What Drives the Price per Square MetreRailway and HSR Noise Barriers: Design for Speed and ClearanceAluminum Alloy Noise Barrier SupplierGabion Basket Supplier6m High Noise Barrier2m High Noise BarrierFence Cost Per Metre: What Actually Moves the Price of a Boundary FenceNoise Control SolutionsMetal Noise Barrier ManufacturerConstruction Site Fencing: Temporary Panels, Welded Mesh or Hoarding4 Meter Noise Barrier Panel