A container terminal is one of the few places where the noise source is both tall and mobile. A straddle carrier puts its diesel engine and its hoist machinery at eight to twelve metres above the ground and then drives the whole assembly around the yard. A boundary wall at three metres does not screen a source at that height, and a barrier sized for a road is the wrong shape for the problem.
This is why port noise complaints often persist after a wall has been built. The wall screens the yard surface and the terminal tractors, which are the quieter part of the problem, and leaves the dominant plant visible and audible over the top. Getting a terminal quiet enough usually needs a mix: source treatment on the plant itself, screening placed close to the plant rather than at the boundary, and a boundary treatment that handles what is left.
Straddle carriers and RTGs — diesel engine under load, hoist winch, and the impact of the spreader landing on the container. The engine is the continuous component; the impact is impulsive and travels.
Reach stackers and empty handlers — engine plus hydraulic whine, usually at lower height but closer to the boundary in a small yard.
Ship-to-shore cranes — gantry travel and trolley, plus the same container impact, at height and often over water.
Reefer racks — compressor hum, tonal and continuous, running all night in blocks of dozens of units.
Terminal tractors and trucks — the ground-level component that a boundary wall does screen effectively.
The character matters as much as the level. Engine noise is concentrated at 63–250 Hz, container impact is broadband and impulsive, and reefer plant is tonal. A single number for the yard tells you almost nothing about which treatment will work.
Barrier performance depends on breaking the line of sight between source and receiver. With a source at ten metres and a boundary wall at three, the line of sight passes well above the wall for any receiver more than a short distance away, and the barrier is working only through diffraction over its top edge. The insertion loss collapses, and the wall becomes an expensive visual screen.
Height is the obvious answer and usually the wrong one. A boundary wall tall enough to screen a straddle carrier from a nearby residential block would be eight to ten metres, which is a planning and cost problem before it is an acoustic one. The alternative is to move the screen towards the source.
On a terminal, treating the plant is usually cheaper per decibel than building height at the boundary, and it works regardless of receiver position.
Engine enclosures and silencers on straddle carriers and RTGs, with the enclosure designed for the actual duty cycle rather than catalogue figures.
Electrification of RTGs, which removes the diesel engine from the yard entirely and is the single largest step available.
Impact softening at the spreader, which reduces the impulsive component that barriers handle worst.
Reefer rack orientation and enclosure, since a compressor bank is a fixed source that can be enclosed at modest cost.
Placing the barrier along the yard edge, between the operating area and the sensitive boundary, puts it much closer to the source. Two things follow. The barrier intercepts the line of sight at a shorter distance, so a given height buys more attenuation. And the barrier can be set to the height of the plant it screens, typically six to ten metres, rather than to a boundary height that planning will accept.
| Source | Dominant character | Control that works |
|---|---|---|
| Straddle carrier engine | Low frequency, continuous, source at 8–12 m | Engine enclosure, plus yard-edge screen at plant height |
| Container impact | Impulsive, broadband | Impact softening at spreader; absorption on screen face |
| Reefer racks | Tonal, continuous, fixed | Local enclosure or rack orientation away from boundary |
| Terminal tractors | Broadband, ground level | Boundary wall is effective here |
A coastal terminal is a C5 marine environment, and a barrier specified for a road will not survive it. The failures are predictable: galvanised posts showing red rust at the splash zone within a few years, mild steel fixings seized solid, and perforated absorptive facings clogged with salt and dust so that the absorption decays without anyone noticing.
Duplex coating — hot dip galvanising plus a topcoat — rather than galvanising alone, for anything within splash height.
Stainless or sheradised fixings, because a rusted bolt turns a maintenance task into a cutting job.
Concrete panels where mass is wanted and the budget allows, since concrete is the one material that genuinely tolerates a marine atmosphere.
Drainage and cleanability designed in, so that the absorptive face can actually be washed.
Any screen inside the yard has to stay outside the operating envelope of the cranes and the turning circles of the plant. A barrier that a straddle carrier can clip is a safety item, and the clearance required is not always obvious from a plan. The layout should be agreed with terminal operations, not only with the acoustic consultant, and the barrier should carry impact protection at the corners where plant passes closest.
Terminals run at night, which changes the assessment. Background levels drop, so the same source becomes more noticeable, and rating schemes frequently apply a penalty for tonal and impulsive content. Both the reefer compressors and the container impacts attract that penalty, and it can add several decibels to the rated level without any change in the measured sound pressure.
This is the argument for treating tonal and impulsive sources at source rather than trying to absorb the penalty with barrier height. A tonally penalised source needs a larger reduction than a broadband one to reach the same rated level, and height is an inefficient way to buy it.
Source inventory with height, duty cycle and frequency character for each item of plant.
Clear split between source control and screening, with the expected reduction from each.
Screen position agreed with terminal operations, outside crane and plant envelopes.
Corrosion category stated, with coating system and fixing grade to match.
Absorptive faces cleanable, with an access method that does not need scaffolding every time.
Night-time tonal and impulsive content assessed, not just the daytime LAeq.
Related reading: noise barrier structure and panel selection, industrial noise barrier systems, and perforated metal absorptive panels.
Only partly. It screens ground-level plant such as terminal tractors effectively, but straddle carriers put their engines eight to twelve metres up, so the line of sight passes over a normal boundary wall and the insertion loss falls away. Screening closer to the plant, at plant height, does more.
Tall enough to break the line of sight from the plant to the sensitive receiver, which for a straddle carrier usually means six to ten metres. That is only feasible because the screen sits inside the terminal, close to the source; the same height at the boundary would rarely be permitted.
Usually yes, for the noise from the RTGs themselves. Removing the diesel engine removes the dominant continuous source rather than screening it, which works for every receiver at once. The barrier then only has to deal with the remaining plant.
Concrete performs best in a marine atmosphere and gives mass at low frequency. Where weight or foundations rule it out, a duplex-coated metal panel with stainless fixings is the practical alternative, provided the absorptive face can be washed.
Because the background drops and because rating schemes add a penalty for tonal and impulsive content. Reefer compressors are tonal and container impacts are impulsive, so the rated level can rise by several decibels even when the measured level is unchanged.
Contact Us
Imfornation
Air Source Heat Pump Noise Barrier: Screens and AirflowInfrastructure Noise ControlRailway Station Noise: Platforms, Plant and ApproachesMetal Noise Barrier ManufacturerDouble Wire Fence: 868 and 656 Panels, Posts and FixingsNoise Barrier Wind Load: Posts, Spacing and Foundations1115m High Noise BarrierBiomass and CHP Noise: Fans, Vents and Continuous DutyRoad Engineering Noise Barrier: Sections and StructuresGabion Baskets for sale1Noise Barrier Height: How the Height Is Actually SetGabion Retaining Wall: Sizing, Drainage and Stone FillMining and Quarry Noise Barriers: Dust, Plant and LayoutMetro Depot Noise Barrier: Enclosure for Depots and Over-Track DevelopmentAirport Noise Barrier: Ground Noise, Run-Up and Plant2m High Noise Barrier3D Curved Fence Panel Manufacturers0.85 NRC Noise Barrier Wholesale4 Meter Noise Barrier PanelGabion Basket SupplierCar Park Noise: Ventilation, Ramps and Rooftop PlantSchool Noise Barrier: Cutting Traffic Noise at the ClassroomTunnel Portal Noise: Hoods, Barriers and AbsorptionPort Container Terminal Noise Barrier: Straddle Carriers and Yard EdgesToll Plaza Noise: Canopy Reflection and AccelerationCutting and Embankment Noise Barrier: Section GeometryNoise Barrier Installation: Sequence, Posts and SealsFence Cost Per Metre: What Actually Moves the Price of a Boundary FenceRoad Viaduct Noise Barrier: Deck Edge, Parapet and Load LimitsUrban Noise ControlNoise barriers costIntercity Railway Noise Barrier: Mixed Traffic LinesAt-Grade Railway Noise Barrier: Level Crossings and Track AccessAluminum Alloy Noise Barrier SupplierResidential Noise Barrier: Height, Planning and Appearance6m High Noise BarrierFreight Railway Noise Barrier: Low Speed, High MassPoultry Farm Noise: Ventilation Fans and GeneratorsHospital Noise Barrier: Ward Targets, Height and CleanabilityBridge Deck Noise Barrier: Load, Movement and AccessShopping Centre Noise: Rooftop Plant and DeliveriesData Centre Cooling Noise: Louvre Screens and AirflowHighway Noise Barrier Cost: What Drives the Price per Square Metre