hotproduct

Sign Gantries and Noise Barriers: Passing Structures Through a Barrier Line

In short: a barrier is only as good as its weakest penetration. Every gantry leg, lighting column, camera mast, access door and drainage outlet is a hole in the acoustic line, and the leak is local but real. Designing those details before the barrier is ordered costs almost nothing; correcting them afterwards means removing panels.

On a long barrier the penetrations are the parts that generate complaints, because a resident looking at the barrier from an upper floor sees the gaps and hears through them. The acoustic calculation, which usually assumes a continuous line, does not include them, which is one reason measured performance can fall short of the prediction.

Why do penetrations matter acoustically?

Because sound does not need a large opening. A gap of a few millimetres running the full height of a panel, or an unsealed collar around a 300 mm column, is enough to transmit a noticeable amount of energy at the frequencies that dominate traffic noise.

  • The gap is a path, not a hole. Even a narrow slot radiates efficiently when its depth is small relative to the wavelength.

  • Diffraction around the opening spreads sound to receivers that the barrier was meant to screen.

  • Resonance in a deep slot can transmit more at some frequencies than the panel transmits overall.

  • Multiple penetrations add up. A barrier with a door, two gantries and a lighting column every 30 m is not the barrier that was modelled.

How large is the effect of a penetration?

It depends on the opening, on its distance from the receiver and on the barrier height. As an indicative guide, a single well-sealed structural penetration has a small local effect, while an unsealed slot or an open doorway can remove a noticeable part of the benefit over a distance of several metres either side.

The honest statement for a design report is that the effect is local in extent and variable in magnitude, and that the way to control it is to detail every penetration as an acoustic item rather than to predict a single number for it.

What are the ways to pass a gantry leg through a barrier?

DetailHow it worksWhen to use it
Barrier stops either side, gantry leg stands in a clear gapSimplest, but leaves an open slot the full heightOnly where the gap can be closed by a separate screen behind the leg
Panels cut to the leg with a sealed collarBarrier is continuous, the leg passes through a tight collarPreferred where the leg is vertical and access allows sealing
Barrier returns around the leg in a UKeeps the acoustic line outside the structureWhere the leg is wide or the barrier can afford the length
Barrier carried on the gantry, above the signMaintains height across the openingWhere the gantry is at the barrier line and height matters

How are lighting columns and camera masts handled?

The same way, with one addition: these items need to be reachable. A column base sealed inside a barrier cannot be inspected or re-torqued, and an access door in the barrier for every column is itself a leak.

  • Group services where possible, so one access door serves several items.

  • Use a collar that is removable, so the base can be inspected without dismantling panels.

  • Keep the column base outside the barrier line where the geometry allows, with the arm reaching over.

  • For camera masts, expect future replacement; design the seal to be re-made, not cut once.

What about emergency egress and maintenance doors?

A door in a noise barrier is a performance item, not a joinery item. It needs to close against a seal, to be self-closing where it is an escape door, and to be rated for the same wind load as the panels around it.

The most common failure is a door that is left open or propped, which produces a leak far larger than any detail could compensate for. Where a door is routinely used, the acoustic answer is a lobby: two doors with a short return between them, so that one is normally closed.

How are drainage and cable ducts sealed where they cross?

With a flexible boot or a grouted sleeve, not with mortar packed around a pipe. Rigid mortar cracks as the ground and the structure move, and a cracked seal at the base is the most common source of a barrier that measures worse than it should.

Where a drain has to pass under the barrier line, the better detail is to route it around the foundation rather than through the barrier, so that the water path and the acoustic line do not have to be reconciled in one detail.

What does a good acoustic collar look like?

  • Fixed to the panel, not to the column, so that column movement does not open the seal.

  • Flexible enough to accommodate thermal and dynamic movement of the structure.

  • Removable in sections, for inspection and re-torque.

  • Non-absorbent, because a collar that holds water will degrade and then leak.

  • Detailed on the barrier drawing, with the column dimension, not left to site.

Standards and references

  • EN 14388 — product specification for road traffic noise reducing devices.

  • EN 1793-2 — airborne sound insulation rating, which assumes a sealed specimen.

  • EN 1794-1 — mechanical performance, including wind load on doors and fixings.

  • ISO 10847 — in-situ insertion loss, the method that reveals penetration leaks.

Related reading: noise barrier structure and panel selection, installation sequence and tolerances, and barrier maintenance.

Sign Gantries and Noise Barriers: Passing Structures Through a Barrier Line

Frequently asked questions

Do penetrations reduce noise barrier performance?

Yes, locally. Each gantry leg, column, mast or door interrupts the acoustic line, and an unsealed gap transmits sound even when it is narrow. The effect is limited in extent but can be noticeable immediately beside the penetration.

How should a gantry leg pass through a barrier?

Best practice is to keep the barrier continuous and cut the panels to the leg with a sealed, removable collar. Stopping the barrier either side of the leg leaves a full height slot and should only be used with a separate screen behind it.

Why do barrier doors cause problems?

Because they are often left open or propped, which creates a leak larger than any detail can compensate. Where a door is in routine use, a two door lobby with a short return keeps one leaf closed.

How are pipes and ducts sealed at the barrier base?

With a flexible boot or grouted sleeve rather than mortar, because mortar cracks as ground and structure move. Better still, route the drain around the foundation so the acoustic line and the water path do not share a detail.

Can penetration leaks be found after construction?

Yes, by in-situ insertion loss measurement to ISO 10847 taken on both sides of the barrier. A result well below the design prediction usually points to a penetration or a base seal rather than to the panels.

Contact Us

Imfornation

Noise Control Solutions5m High Noise BarrierAt-Grade Railway Noise Barrier: Level Crossings and Track Access3D-Welded Mesh fencing system2m High Noise BarrierNoise barriers costResidential Noise Barrier: Height, Planning and Appearance1Substation and Transformer Noise Barriers: Controlling Low-Frequency HumNoise Barrier Maintenance: Inspection and RepairConstruction Site Fencing: Temporary Panels, Welded Mesh or HoardingIndustrial Plant Noise Barrier: Boundary Wall and Equipment EnclosureExpressway Widening: Upgrading an Existing Noise Barrier111Chain Link Fence: Wire, Mesh and Coating SelectionNoise Barrier Height: How the Height Is Actually SetMetro Viaduct Noise Barrier: Deck Radiated NoiseHighway Noise Barrier Foundation: Piles, Footings and Soft GroundHighway Noise Barrier Cost: What Drives the Price per Square MetreNoise Barrier Installation: Sequence, Posts and SealsAirport Noise Barrier: Ground Noise, Run-Up and PlantTemporary Fence: Panels, Ballast and Wind Load on SiteStadium Noise Barrier: Crowd, PA and Plant Compounds29 STC Noise Barrier WholesaleHighway Service Area Noise Barrier: HGV Parking, Plant and NeighboursBridge Deck Noise Barrier: Load, Movement and AccessTunnel Approach Noise Barrier: Open Cut, Portal and Cut-and-CoverData Centre Cooling Noise: Louvre Screens and AirflowAluminum Alloy Noise Barrier SupplierRoad Engineering Noise Barrier: Sections and StructuresCar Park Noise: Ventilation, Ramps and Rooftop PlantIntercity Railway Noise Barrier: Mixed Traffic Lines0.85 NRC Noise Barrier WholesalePlace of Worship Noise Barrier: Chimes, PA and PlantSign Gantries and Noise Barriers: Passing Structures Through a Barrier LineRail Overbridge Noise Barrier: When the Bridge Is the SourceNoise Barrier Wind Load: Posts, Spacing and FoundationsMetro Depot Noise Barrier: Enclosure for Depots and Over-Track DevelopmentHospital Noise Barrier: Ward Targets, Height and CleanabilityRailway and HSR Noise Barriers: Design for Speed and ClearanceBridge Widening Noise Barrier: Joining a Barrier Across Two DecksCutting and Embankment Noise Barrier: Section Geometry4 Meter Noise Barrier PanelGabion Mattress: Channel Lining and Scour ProtectionConstruction Site Noise Barriers: Temporary Screens That Move With the Works