A double wire fence is a welded panel with two horizontal wires at every horizontal line instead of one. That single change is what makes the panel rigid enough to need no tensioning, no top rail and no bottom wire — which is why it installs faster than chain link at a comparable height.
The numbers are the wire diameters, read left to right: the two outer horizontal wires, then the vertical wire.
| Type | Wire arrangement | Character |
|---|---|---|
| 868 | 8 mm / 6 mm / 8 mm | Heavy panel, the common choice for site perimeter and sports |
| 656 | 6 mm / 5 mm / 6 mm | Lighter panel, lower cost, still self-supporting |
| 2D | Flat panel, same double-wire construction | Straight lines, tighter budget |
| 3D | Panel with horizontal V-bends | Stiffer for the same wire, and the bend line reads as a design feature |
The V-bends in a 3D panel add stiffness without adding wire, which is why a 3D panel can span wider post spacing than the equivalent flat panel.
Chain link is a fabric and has to be pulled tight between posts. A double wire panel is a rigid welded grid: it holds its own shape, so the frame only has to support it.
What follows on site: no top rail, no bottom tension wire, no straining. Panels clamp directly to the posts, which cuts installation time and removes the most common call-back on a fence — sagging fabric.
Square hollow section posts — 60 × 60 mm is typical, with clamps or brackets at each panel edge. The most common arrangement.
I-profile posts — the panel slots into the post rather than clamping to the face, which gives a cleaner line and hides the fixings.
Round posts — used where the fence follows a curve.
Whatever the post, the fixing is the joint that decides whether the fence stays straight. Bolted clamps at top and bottom of each panel edge; a single fixing per panel allows the panel to rotate.
It suits applications where you need a rigid, low-maintenance barrier with a clean appearance and a quick install:
Industrial and commercial site perimeters.
Sports grounds and training pitches, where the panel absorbs ball impact without permanent deformation.
School and park boundaries, where the fence is visible and appearance matters.
Anywhere a chain link run would sag over time and need re-tensioning.
It is less suitable where the requirement is anti-climb specifically — the apertures are large enough to provide footholds — or where the fence has to follow tight curves.
Panels are normally galvanised and then powder coated, which gives the colour and a second corrosion barrier over the galvanising. Green, black, grey and RAL colours are the usual range.
Because the panel is welded before coating, the coating has to cover the weld intersections — that is where an under-specified finish fails first. On coastal sites specify the heavier system rather than the thicker wire.
Both are rigid double wire panels. The choice is usually about span, appearance and budget rather than strength.
| Consideration | 2D (flat) | 3D (V-bend) |
|---|---|---|
| Panel stiffness | Good | Higher for the same wire |
| Post spacing | Around 2.5 m | Up to about 3.0 m |
| Appearance | Plain grid, minimal shadow line | Visible horizontal bands, reads as a designed fence |
| Cost per metre | Lower | Higher — more steel and more pressing |
| Best for | Long boundaries where cost dominates | Frontage, sports, anywhere the fence is seen |
If the site is exposed and the post spacing is generous, the 3D panel is usually the cheaper answer overall even at a higher panel price, because it needs fewer posts.
Set posts on the line first, at the specified spacing, plumb and to depth, with foundations poured and cured before panels are hung.
Fit the bottom clamp on each post at the panel's lower fixing height.
Lift the panel into place and seat it on the bottom clamp before fitting the top one. Panels are heavy and are handled by two people or a small lifter.
Clamp top and bottom at both panel edges, then check the panel is vertical before final tightening.
Step the line on slopes at post positions, not mid-panel — a rigid panel cannot rack to follow a gradient.
Hang gates last, on their own heavier posts, once the run either side is set.
The one step that gets skipped is checking verticality before tightening. A panel clamped while leaning stays leaning, and the error accumulates along the run.
Total run length, corners and ends.
Height and panel width.
Panel type — 868 or 656, 2D or 3D.
Colour and coating specification.
Gate schedule.
Ground conditions and the post foundation type.
Both use the double horizontal wire. A 3D panel has horizontal V-bends pressed into it, which stiffens the panel and lets it span further between posts. A 2D panel is flat and cheaper, and needs slightly closer post spacing for the same rigidity.
No. The panel is rigid enough to support itself between posts, which is one of its main advantages over chain link. The panel clamps to the posts at its edges.
Not specifically. The mesh apertures are large enough to act as footholds. If the requirement is anti-climb, a 358 mesh fence is the correct product rather than a double wire panel.
Commonly 2.5 m for a flat 2D panel and up to 3.0 m for a 3D panel, subject to wind load and panel height. Wider spacing saves posts and increases panel deflection.
Yes, by stepping the panels. Double wire panels are rigid, so they cannot rack to follow a gradient the way chain link can — the line is stepped in increments instead.
Send us the run length, the height, whether you want 2D or 3D, and the colour, and we will come back with a panel and post specification plus a price per panel.
For the product range see double wire fencing, and for a specification example see double wire fence panels. Where the requirement is anti-climb rather than rigid, see our anti-climb fence specification.
Contact Us
Imfornation
3D-Welded Mesh fencing system16m High Noise Barrier5m High Noise BarrierHospital Noise Barrier: Ward Targets, Height and CleanabilityConstruction Site Noise Barriers: Temporary Screens That Move With the WorksResidential Noise Barrier: Height, Planning and AppearanceSubstation and Transformer Noise Barriers: Controlling Low-Frequency Hum111358 Security Fence: Mesh, Wire and Anti-Climb SpecificationMetro Depot Noise Barrier: Enclosure for Depots and Over-Track DevelopmentCooling Tower Noise Barrier: Layout, Airflow and Panel DesignChain Link Fence: Wire, Mesh and Coating SelectionNoise Barrier Guide: Types, Height, Cost and SelectionAluminum Alloy Noise Barrier Supplier2m High Noise BarrierTemporary Fence: Panels, Ballast and Wind Load on Site4 Meter Noise Barrier PanelNoise Control SolutionsConstruction Site Fencing: Temporary Panels, Welded Mesh or Hoarding3D Curved Fence Panel ManufacturersGabion Basket SupplierNoise barriers cost0.85 NRC Noise Barrier Wholesale3m High Noise BarrierGabion Baskets for saleIndustrial Plant Noise Barrier: Boundary Wall and Equipment Enclosure29 STC Noise Barrier WholesaleDouble Wire Fence: 868 and 656 Panels, Posts and FixingsMetal Noise Barrier ManufacturerFence Cost Per Metre: What Actually Moves the Price of a Boundary FenceSolar Noise Barrier Cost: What Drives the Price and the PaybackRailway and HSR Noise Barriers: Design for Speed and ClearanceSchool Noise Barrier: Cutting Traffic Noise at the ClassroomUrban Noise ControlIndustrial Noise Barrier SystemHighway Noise Barrier Cost: What Drives the Price per Square MetreAnti-Climb Fence Specification: 358 Mesh, Paladin Pales and 3D PanelsInfrastructure Noise Control