Steel fence

Razor Barbed Wire Concertina Coils for Perimeter Protection

Concertina razor wire in BTO-22 and CBT-65 blade profiles, 450-900 mm coil diameter, galvanized or PVC coated, 10 m and 12 m coils for perimeter topping.
  • Razor Barbed Wire Concertina Coils for Perimeter Protection
  • Razor Barbed Wire Concertina Coils for Perimeter Protection
  • Razor Barbed Wire Concertina Coils for Perimeter Protection
  • Razor Barbed Wire Concertina Coils for Perimeter Protection
Razor Barbed Wire Concertina Coils for Perimeter Protection
Galvanized concertina razor wire coil standing upright on a white background

Concertina Razor Wire in Coils and Straight Runs

Razor barbed wire is a galvanized steel strip pressed into blades and wrapped around a core wire, supplied either as a concertina coil that opens into a continuous spiral or as a flat strip that mounts straight along a wall or fence line. The blade does the work; the core wire only holds the blade strip in position. We supply coils from 450 mm to 900 mm diameter in 10 m and 12 m lengths, in galvanized finish or PVC coated. Most orders ship as a topping for an existing fence, a wall extension, or a compound perimeter where the fence below already stops vehicles and the razor wire has to close the climbing route. Every coil is measured before it is packed: coil diameter, blade strip thickness and core wire diameter.

Blade Profile: BTO and CBT

Blade profile is the first specification to fix, because it sets both the cutting geometry and the price. BTO profiles are stamped along one edge of a flat strip, so each blade presents a single point on one face. CBT profiles cross two stamped strips, so the unit carries points on both faces and reads as a denser, more aggressive length of wire. Neither is better in the abstract; they suit different mounting positions and different levels of deterrence.

Within the BTO family, the number after the prefix is the blade length in millimetres. BTO-22, with a 22 mm blade at roughly 76 mm centre-to-centre spacing on a 2.5 mm core wire and a 0.5 mm strip, is the profile most buyers specify and the one we hold in stock. BTO-10, BTO-12 and BTO-18 use shorter blades with tighter spacing, which gives more blades per metre and a lighter coil that suits a low wall top. BTO-28 and BTO-30 use longer blades for a wider visual barrier. In the CBT family, CBT-60 and CBT-65 refer to the 60 mm and 65 mm crossed blade units used where the wire is the primary barrier rather than a topping.

When you compare quotes, compare the strip thickness and the core diameter, not only the profile name. A nominal BTO-22 built on a 0.4 mm strip over a 2.0 mm core weighs noticeably less per coil than one on 0.5 mm over 2.5 mm, and it will deform sooner when something is thrown against it.

Close-up of pressed razor wire blades on a galvanized core wire

What the Blade Strip Actually Measures

Caliper measuring the thickness of a razor wire blade strip

Four numbers decide what a coil really is, and all four can be checked with a caliper in under a minute. Blade length runs from the core wire to the blade tip. Blade spacing is measured centre to centre between adjacent blades along the strip. Strip thickness is the gauge of the flat steel the blades are stamped from. Core wire diameter is the round wire the strip is wrapped around and the part that carries the tension of the run.

Two coils sold as the same profile can differ enough to change the job. A heavier strip holds a sharper edge longer and resists bending when the wire is tensioned, but it costs more per metre and adds weight to every bracket. A thinner core makes the coil easier to open and handle but sags over longer spans between supports. That is why we quote the strip thickness and core diameter next to the profile rather than leaving them implied.

Coil weight is the quickest cross-check on a delivery. Weigh one coil on a scale and divide by the nominal length; if the result is well under the figure in the offer, the strip or the core is lighter than specified. We state coil weight in the quotation so the check can be made on arrival rather than after installation.

Coil Diameter, Coil Length and How It Deploys

Coil diameter is the measurement across the open spiral, and it controls how much wall top or fence line the coil covers. A 450 mm coil gives a tight spiral that sits neatly on a narrow wall coping and needs little clearance. A 500 mm coil is the usual middle choice for fence toppings. At 700 mm and 900 mm the spiral covers a much wider band and reads as a serious barrier from a distance, but the coil is heavier, needs stronger support arms, and must be set back from any walkway it could overhang.

Standard coil lengths are 10 m and 12 m, supplied compressed and tied. To deploy, fix support arms or brackets at 2 m to 3 m centres and tie the coil to each arm with stainless or galvanized wire, then release the ties progressively from one end so the spiral opens along the run. Overlap each coil by about one complete turn onto the next so the spiral reads as continuous; a butt joint leaves a gap that is exactly where someone will test the fence.

For wall tops and roof edges, the flat strip version mounts directly on brackets with no spiral at all, which keeps the profile low and avoids an overhang. Where the fence turns a corner, brace the arm on the outside of the turn, because that is where the tension in an opened spiral pulls hardest.

Tape measure checking the diameter of a concertina razor wire coil
Green PVC coated razor wire coil on a white background

Galvanized or PVC Coated

Galvanized is the default finish and the right one for most inland sites. The zinc coating protects the strip and the core wire, and the bright finish is easy to inspect on delivery. On a coast, or anywhere the air carries salt or industrial sulphur, specify a heavier zinc coating rather than assuming the standard one will hold; razor wire has a thin section at every blade edge and that is where corrosion starts.

PVC coating adds a coloured jacket over the galvanized strip. Green is the most requested colour because it visually ties the topping to a mesh or welded fence below and is less conspicuous than bright zinc from the road. Dark green and black are also used where the wire sits against a dark wall or a treeline. The coating adds a small amount to the strip thickness, gives a softer, grippier surface, and delays the start of corrosion at the blade faces, but it does not seal the cut blade edge, so a PVC coil in a coastal location still benefits from a properly galvanized strip underneath.

Colour also has a practical function beyond appearance. A bright galvanized coil at eye level is highly visible, which is useful where the barrier is meant to be seen and avoided; a coated coil in a dark colour is chosen where the wire should sit quietly above a boundary without drawing attention. Tell us which effect you want and we will quote the finish that produces it.

Packing, Container Loading and What to Send

Razor wire coils packed in protective wrapping and loaded inside a shipping container

Coils are compressed, tied, and wrapped in heavy paper or woven fabric before stacking, because an unprotected coil will abrade itself and every handling point becomes a rust site before it reaches site. Wrapped coils are stacked in the container and braced against movement; loading is planned by total weight and by coil diameter, since large coils take floor space faster than they take payload. Tell us the tonnage or the total metreage and we will work back to the coil count and the container plan that loads cleanly.

To quote accurately we need six things: the blade profile you want, the coil diameter, the coil length, the finish, the total length of run in metres, and what the wire will be mounted on. A photo of the wall top or fence line is often the fastest way to settle the mounting question, and a sample of the wire already on the property is useful when you are trying to match an existing barrier.

Hebei Jinbiao has manufactured wire and fencing products for 30 years and supplies CE-marked goods with ISO 9001, ISO 14001 and ISO 45001 management systems. Overseas projects are supplied only; installation is not included. Send the run length and the mounting detail and we will come back with the profile, coil size and packing plan for your site.