hotproduct

Quarry Noise Control: Crushers, Screens and Blasting

In short: a quarry has two acoustically unrelated problems. Crushers, screens and conveyors are continuous broadband sources that can be enclosed, housed or screened. Blasting is an impulsive, low frequency event that no barrier can meaningfully attenuate, and it has to be managed by charge design and by timing rather than by structure.

Treating them as one problem produces the familiar outcome: a substantial barrier around the plant boundary, complaints that continue after it is built, and no explanation for why. Separating the sources first, then choosing a measure per source, is both cheaper and more effective.

What are the noise sources at a quarry?

  • Primary crusher — continuous, broadband, dominant at low to mid frequency.

  • Screens — continuous, with strong tonal components from the mechanism and impact from material on the deck.

  • Conveyors and transfer points — impact noise at each transfer, plus drive units.

  • Loading and hauling — engines, reverse alarms, bucket and body impacts.

  • Blasting — impulsive, low frequency, with air overpressure and ground vibration.

SourceAcoustic characterMeasure that works
Primary crusherContinuous, broadband, low to mid frequencyEnclosure with mass, sealing, isolation, silenced ventilation
ScreensContinuous, tonal plus impactEnclosure, resilient deck mounts, sealed chutes
Conveyor transfersImpact, repeated at each pointEnclose the transfers and drives, resilient idlers
Loading and haulingEngine plus reverse alarms, intermittentRoute control, alarm type, berms and stockpiles
BlastingImpulsive, below about 20 to 50 HzCharge design, delay sequencing, timing; not a barrier

Why can a barrier not control blasting noise?

Because the energy is at frequencies where a barrier of practical height does nothing, and because the source is a ground level event that generates air overpressure travelling over the barrier rather than through the line of sight.

A barrier attenuates by interrupting the direct path and by diffracting sound over its top. Blast overpressure has most of its energy below about 20 Hz to 50 Hz, where the wavelengths are tens of metres and the barrier is acoustically small. The barrier also cannot reduce ground vibration, which is often what residents feel and report as noise.

How do you enclose a primary crusher?

With a building, not with a barrier. A crusher enclosure is a structure with walls, a roof, ventilation and access, and its performance depends on mass, on sealing and on how the plant is isolated from the structure.

  • Mass in the walls and roof is the primary variable; a light cladding gives little attenuation at low frequency.

  • Sealing matters more than mass once the enclosure is closed, because openings short-circuit the walls.

  • Ventilation must be silenced; an unsilenced fan opening can dominate the enclosure performance.

  • Isolation of the crusher from the structure prevents the enclosure itself becoming a radiator.

  • Access for liner changes has to be designed as an acoustic door, not added later.

What about screens and conveyors?

Screens are the second most common complaint source and are often overlooked because the crusher attracts the attention. The dominant paths are the screen mechanism itself, the impact of material on the deck, and the structure that transmits both.

Conveyors are a series of point sources at the transfers, not a line source. Enclosing the transfer points and the drive units, and using resilient idlers in sensitive locations, usually achieves more per unit cost than screening the whole conveyor run.

Can stockpiles be used as barriers?

Yes, and they are often the cheapest screen on a quarry site. A stockpile is effectively an earth berm: it has mass, it is free because the material has to be somewhere, and it can be shaped.

  • Height matters more than length; a stockpile below the line of sight provides little attenuation.

  • Slope stability limits how steep it can be, which sets how close it can be to the source.

  • Stockpile location changes with production, so an acoustic function has to be written into the site plan to survive.

  • Dust and drainage from the stockpile can conflict with the plant it is screening.

How does topography change the answer?

More than any barrier does. A quarry is usually a depression, and the rim of the excavation is a natural screen for receivers outside it. Where the rim is above the plant, the boundary barrier may be unnecessary; where the site is on a slope and the plant is at the high end, no barrier at the boundary will help the receivers below.

This is why a quarry noise assessment that uses flat ground propagation loses the single largest variable on the site. Terrain should be in the model before any barrier is sized.

What measurements are needed?

  • Separate the continuous plant sources from the impulsive blast events; they need different descriptors.

  • For plant, use equivalent level over a representative period, with the plant in normal operation.

  • For blasting, record the event itself — peak level, rise time and spectrum — not a short equivalent level.

  • Measure at the boundary and at the nearest dwellings, because the two can differ in which source dominates.

  • Note ground vibration separately; it is assessed on its own criteria and is not fixed by acoustic measures.

Standards and references

  • ISO 1996-1 and ISO 1996-2 — description, measurement and assessment of environmental noise, including impulsive and tonal adjustments.

  • ISO 9613-2 — outdoor sound propagation, for plant noise modelling over terrain.

  • EN 14388 and EN 1793-1 — barrier product specification and absorption rating.

  • EN 1794-1 — mechanical performance of barriers, including wind load in exposed sites.

Related reading: mining and quarry barriers, industrial noise barrier systems, and gabion retaining walls.

Quarry Noise Control: Crushers, Screens and Blasting

Frequently asked questions

Can a noise barrier reduce quarry blasting noise?

Not meaningfully. Blast overpressure has most of its energy below roughly 20 Hz to 50 Hz, where wavelengths are tens of metres and a practical barrier is acoustically small. Blasting is controlled by charge design, delay sequencing and timing.

How do you reduce crusher noise?

By enclosing the crusher in a building with mass in the walls and roof, sealing the envelope, silencing the ventilation, and isolating the machine from the structure so the enclosure does not itself radiate.

Are stockpiles effective noise barriers?

They can be, and they cost little because the material has to be stored somewhere. Their effectiveness depends on height relative to the line of sight, on slope stability, and on whether their acoustic function is protected in the site plan as production moves.

Why does topography matter more than the barrier?

Because a quarry is usually a depression, and the excavation rim screens receivers outside it. A model that assumes flat ground misses the largest single factor, and can lead to a barrier being sized for a problem the terrain has already solved.

Which quarry source is usually dominant at the nearest house?

Often the screens rather than the crusher, because screens are higher, more open and generate both mechanism tones and impact noise. Measurements at the dwelling, not only at the boundary, are needed to confirm it.

Contact Us

Imfornation

Sign Gantries and Noise Barriers: Passing Structures Through a Barrier LineRail and Transit Noise Barrier: Lines, Stations, DepotsBridge Widening Noise Barrier: Joining a Barrier Across Two DecksLaboratory Noise: Fume Hoods, Compressors and VibrationNoise Barrier Height: How the Height Is Actually SetNoise Barrier Maintenance: Inspection and RepairAirport Noise Barrier: Ground Noise, Run-Up and Plant29 STC Noise Barrier WholesaleMetal Noise Barrier ManufacturerNoise Barrier Wind Load: Posts, Spacing and FoundationsSchool Noise Barrier: Cutting Traffic Noise at the Classroom3D-Welded Mesh fencing systemNoise Barrier Structure and Panel Selection: 2 m to 6 mWastewater Plant Noise: Blowers and Continuous PlantBiomass and CHP Noise: Fans, Vents and Continuous DutyTunnel Approach Noise Barrier: Open Cut, Portal and Cut-and-CoverRailway and HSR Noise Barriers: Design for Speed and Clearance3D Curved Fence Panel ManufacturersPerforated Metal Noise Barrier: Open Area and AbsorptionDouble Wire Fence: 868 and 656 Panels, Posts and FixingsNoise Barrier Panel Specifications: The Six NumbersShopping Centre Noise: Rooftop Plant and DeliveriesNoise barriers costToll Plaza Noise: Canopy Reflection and AccelerationGabion Mattress: Channel Lining and Scour ProtectionHighway Noise Barrier Cost: What Drives the Price per Square MetreIndustrial Plant Noise Barrier: Boundary Wall and Equipment EnclosureResidential Noise Barrier: Height, Planning and AppearanceMetro Depot Noise Barrier: Enclosure for Depots and Over-Track DevelopmentAluminum Alloy Noise Barrier SupplierNoise Barrier Installation: Sequence, Posts and SealsTemporary Noise Barrier: Rent or Buy, and What Drives Cost358 Security Fence: Mesh, Wire and Anti-Climb SpecificationGenerator Noise Barrier: Tonal Noise and AirflowQuarry Noise Control: Crushers, Screens and BlastingTunnel Portal Noise: Hoods, Barriers and AbsorptionAt-Grade Railway Noise Barrier: Level Crossings and Track Access111Temporary Fence: Panels, Ballast and Wind Load on SiteNoise Barrier Guide: Types, Height, Cost and SelectionAnti-Climb Fence Specification: 358 Mesh, Paladin Pales and 3D Panels4 Meter Noise Barrier PanelPoultry Farm Noise: Ventilation Fans and Generators3m High Noise BarrierPlace of Worship Noise Barrier: Chimes, PA and Plant