hotproduct

Laboratory Noise: Fume Hoods, Compressors and Vibration

A laboratory is unusual because it is a source and a receiver at the same time. Fume hood exhaust fans and compressors radiate to the neighbours, while the instruments inside are themselves sensitive to noise and vibration. A barrier can serve both purposes, but it is addressing two different problems and the designs are not the same.

The two directions to consider

DirectionTypical sourceWhat helps
Outward to neighboursFume hood exhaust fans, chillers, compressorsScreening, silencing, discharge re-aiming
Inward to instrumentsRoad, rail, neighbouring plant, building servicesBarrier plus building fabric, and vibration isolation

Most laboratory acoustic projects address only one direction and are surprised by the other.

Where laboratory noise comes from

  • Fume hood exhaust fans — usually the dominant source; continuous, often on the roof, and numerous because every hood needs its own path.

  • Compressors and vacuum pumps — tonal, often in a plant room with ventilation openings that leak.

  • Chillers and condensers — as on any building, but frequently sized larger because of equipment cooling loads.

  • Air handling — high air-change rates mean large fans and large ducts, both of which radiate.

  • Emergency generators — tested regularly, tonal, and often close to a boundary on a constrained site.

The exhaust stack problem

Fume hood exhaust has a constraint that most plant does not: the discharge must clear the building's own air intakes and must not re-entrain into them. That fixes the stack height and often the discharge velocity, which in turn fixes much of the noise.

  1. Stack height is set by dispersion, not acoustics, so the source ends up high and above the barrier line.

  2. High velocity discharge is noisy but is required for plume clearance, so reducing it is not usually available.

  3. Multiple small stacks are harder to treat than one large one, because each is a separate source.

The effective measures are silencers in the exhaust duct and careful orientation, rather than a screen at ground level. Where a screen is used, it addresses the fan casing noise rather than the stack discharge.

Vibration is often the real issue indoors

Where a laboratory reports problems with sensitive instruments, the cause is frequently structure-borne rather than airborne, and a barrier does nothing for it:

  • Compressors and pumps transmit vibration into the structure through their mountings.

  • Footfall and door movement on upper floors affect sensitive balances and imaging equipment.

  • Road and rail traffic enters through the ground, not through the windows.

  • Building services — pumps, fans and lifts — are continuous sources connected directly to the structure.

Inertia bases, resilient mounts and structural breaks address these. Screening a facade while leaving the vibration path intact produces no improvement in the instrument's environment.

Protecting the laboratory from outside noise

Where the requirement is inward, the barrier works on the normal principle but the receiver is unusually demanding:

ConsiderationEffect
Receiver heightUpper floors look over barriers; height must be set against the actual window level
OpeningsAny openable window defeats the facade performance; barrier design must assume closed
DistanceA lab close to a road gains less from a barrier than one set back
Continuous sourcesRoad and rail noise is continuous; a steady residual is harder to tolerate than intermittent peaks

Where a barrier earns its place

  • Around a plant compound — compressors, chillers and generators in a defined area with a clear boundary.

  • At the roof edge where exhaust fans are set back from it.

  • Between the site and a neighbouring dwelling, for the residual after source measures.

  • As facade protection, where instruments face an external source and the building fabric alone is insufficient.

  • Not across a fume hood discharge, and not as a substitute for vibration isolation.

The order of work matters more than the panel

Laboratory projects go wrong most often because the sequence is wrong, not because the barrier is wrong. A defensible order:

  1. Establish the direction and the receiver. Neighbours, instruments, or both. Each leads to a different design.

  2. Separate airborne from structure-borne. If instruments are affected, test the vibration path before buying any screening.

  3. Treat the source first where it is a fan, compressor or generator — silencers, mounts, enclosures. This is usually cheaper per decibel than site screening.

  4. Then screen what remains, positioned against the dominant path rather than at the boundary.

  5. Re-measure at the receiver, at the same condition as the baseline.

Skipping step two is the most expensive mistake available on a laboratory project, because the remedy for vibration is invisible in any acoustic product catalogue and cannot be retrofitted into a barrier once it is built.

What to send for a laboratory proposal

  1. Whether the problem is outward (neighbours) or inward (instruments), or both.

  2. Fume hood count, exhaust arrangement, stack heights and discharge velocities.

  3. Compressor, pump and chiller inventory with positions.

  4. Generator rating and test schedule.

  5. For inward problems: which instruments, and whether vibration or airborne noise is the issue.

  6. Nearest dwellings, and the applicable criterion.

Item five matters most: if the problem is vibration, a barrier is the wrong purchase and the enquiry should say so.

Related reading: noise barrier panel range, acoustic louvres for plant rooms, and industrial plant noise barriers.

Laboratory Noise: Fume Hoods, Compressors and Vibration

Frequently asked questions

What is the noisiest equipment in a laboratory building?

Usually the fume hood exhaust fans, because there are many of them, they run continuously, and they are typically on the roof where the sound radiates freely. Compressors and chillers are next, and emergency generators attract attention because they are tonal and tested regularly.

Can a barrier reduce fume hood exhaust noise?

Only the fan casing noise, not the stack discharge. Stack height is set by dispersion requirements, which puts the discharge above the barrier line. Silencers in the exhaust duct and careful orientation of the discharge are the effective measures.

Will a noise barrier help with vibration affecting instruments?

No. Vibration reaches instruments through the structure, not through the air, so a screen has no effect on it. Inertia bases, resilient mounts and structural breaks are the relevant measures, and they should be assessed before any acoustic screening is bought.

Can a barrier protect a laboratory from road noise?

It can contribute, but the facade does most of the work and any openable window defeats it. A barrier is most useful where the lab is at ground or lower-floor level and set back from the road, and where windows are kept closed with mechanical ventilation.

Why is a laboratory harder to protect than an office?

Because the receiver is more demanding and the sources are more numerous. Instruments may be sensitive to levels and frequencies that would be irrelevant in an office, while the building itself generates more noise through high air-change rates and continuous exhaust.

Contact Us

Imfornation

Temporary Noise Barrier: Rent or Buy, and What Drives Cost3D-Welded Mesh fencing system29 STC Noise Barrier WholesalePoultry Farm Noise: Ventilation Fans and GeneratorsIndustrial Plant Noise Barrier: Boundary Wall and Equipment EnclosureDouble Wire Fence: 868 and 656 Panels, Posts and FixingsSchool Noise Barrier: Cutting Traffic Noise at the Classroom3m High Noise BarrierNoise Barrier Panel Specifications: The Six Numbers4 Meter Noise Barrier PanelPlace of Worship Noise Barrier: Chimes, PA and PlantPerforated Metal Noise Barrier: Open Area and AbsorptionTemporary Fence: Panels, Ballast and Wind Load on SiteData Centre Cooling Noise: Louvre Screens and AirflowNoise barriers costNoise Barrier Maintenance: Inspection and RepairConstruction Site Fencing: Temporary Panels, Welded Mesh or HoardingRailway and HSR Noise Barriers: Design for Speed and ClearanceNoise Control SolutionsHospital Noise Barrier: Ward Targets, Height and CleanabilityAnti-Climb Fence Specification: 358 Mesh, Paladin Pales and 3D PanelsInfrastructure Noise ControlWind Farm Noise: What a Barrier Can and Cannot DoNoise Barrier Guide: Types, Height, Cost and SelectionBiomass and CHP Noise: Fans, Vents and Continuous DutyNoise Barrier Height: How the Height Is Actually SetGabion Mattress: Channel Lining and Scour Protection6m High Noise BarrierGenerator Noise Barrier: Tonal Noise and AirflowConstruction Hoarding Panels: Wind Load and Site Boundaries3D Curved Fence Panel ManufacturersMetro Viaduct Noise Barrier: Deck Radiated NoiseLaboratory Noise: Fume Hoods, Compressors and VibrationAir Source Heat Pump Noise Barrier: Screens and AirflowStadium Noise Barrier: Crowd, PA and Plant CompoundsWastewater Plant Noise: Blowers and Continuous PlantSolar Noise Barrier Cost: What Drives the Price and the PaybackMetro Depot Noise Barrier: Enclosure for Depots and Over-Track DevelopmentAluminum Alloy Noise Barrier SupplierGabion Baskets for sale0.85 NRC Noise Barrier WholesaleIndustrial Noise Barrier SystemUrban Noise ControlNoise Barrier Wind Load: Posts, Spacing and FoundationsSubstation and Transformer Noise Barriers: Controlling Low-Frequency Hum