358 security fence is named for its mesh: 3 inches by 0.5 inch, in 8 gauge wire. The numbers matter because they explain the product — a small aperture that a foot cannot get into and a boot cannot kick through, made from wire heavy enough that cutting it takes time and noise.
Three inches by half an inch, with the wires welded at every intersection, produces an opening roughly 76 mm by 13 mm. That is too small for a handhold and too small for a boot. Climbing a 358 panel is not a matter of effort; there is simply nothing to grip and nothing to stand on.
This is also why the panel is specified where the fence line is visible to the public and where an intrusion attempt needs to be slow rather than merely difficult. The mesh is the security feature; the posts only hold it up.
| Property | Typical specification | Note |
|---|---|---|
| Aperture | 76.2 mm × 12.7 mm (3" × 0.5") | The defining dimension |
| Wire diameter | 4.0 mm horizontal and vertical | Heavier wire raises the cut time sharply |
| Panel size | 2.5 m high × 2.2–3.0 m wide | Width is set by post spacing and handling |
| Post section | 60 × 60 mm or 80 × 80 mm square hollow section | Set by panel width and wind load |
Panels are welded, not woven. That is what keeps the aperture fixed under load — a woven panel with these dimensions would distort.
Hot-dip galvanised — the default for industrial and long-life installations. The wire is galvanised before welding and the panel is usually finished after, which is what protects the weld intersections.
Powder coated over galvanised — colour for appearance and a second barrier against corrosion. Common where the fence is in public view.
Marine specification — heavier coating where the site is coastal. Worth specifying up front; retrofitting corrosion protection on a standing fence is not practical.
A 358 panel is only as good as its fixing. Two things decide whether the installed fence performs like the panel does:
Post spacing. Wider spacing means less steel per metre and more panel movement. Beyond about three metres, the panel begins to deflect between posts and the anti-climb property suffers.
Fixings. Full-length clamps or security bolts at every post, not wire ties. A panel tied on with wire can be levered off in a way the mesh itself resists.
358 is frequently combined with a topping — angled cranked arms carrying barbed or razor wire — where the requirement is to stop a determined attempt rather than a casual one. The topping is a separate structural item and adds wind load, so it is designed with the post, not added afterwards.
Gates on a 358 line are usually framed to match the panel and hung on heavier posts. Send the opening width and the required clear height with the enquiry; a gate is priced quite differently from a panel run.
358 is specified for one job: making an intrusion slow and visible. It is not the best choice everywhere, and being clear about that saves money.
| Requirement | 358 fits? | What to use instead |
|---|---|---|
| Stop a foot and a handhold | Yes — this is the design case | — |
| Ball impact, sports perimeter | Poor — the panel deforms and stays deformed | Double wire or 3D panel |
| Long open agricultural boundary | Over-specified and expensive | Chain link or stock fencing |
| Anti-ram vehicle protection | No — a fence is not a barrier | Engineered hostile-vehicle mitigation, designed separately |
| Visual screening | No — you can see straight through it | Add slats, mesh infill or a screen |
The most common specification error we see is using 358 where a double wire panel would do, which roughly doubles the cost for no security gain.
A 358 line reads as a single rigid wall once it is up, which makes the failures look sudden. In practice they occur at two places.
The post foundation. Panels are heavy and catch wind. A post set in a shallow hole looks fine on a still day and leans after the first storm. Foundation depth and concrete volume are set by panel width, height and ground type — not by a standard detail copied across sites.
The panel-to-post fixing. Full-height clamps or security bolts at every post, tightened to the post face. A panel fixed at four points only will bow between posts and open a gap at the joint — and a gap in a 358 line is where the whole system is defeated.
On slopes, 358 panels are stepped rather than racked. The step should be taken at a post, never mid-panel.
Total run length, and the number of corners and ends.
Required height, and whether a topping is needed.
Finish — galvanised, powder coated, or marine.
Site type: coastal, industrial, urban frontage.
Gate schedule with widths and types.
Ground conditions, for the foundation type.
Three inches by half an inch in 8 gauge wire — the mesh aperture and the wire diameter. It is a description of the panel, not a security rating.
Any wire mesh can be cut with the right tool. The point of 358 is that cutting it takes time, makes noise and requires equipment that is hard to carry unnoticed. That is why it is specified where an intrusion has to be delayed and detected, rather than simply blocked.
It is a type of welded mesh fence, but the aperture is much smaller and the wire heavier than a general-purpose welded panel. The two are not interchangeable.
Two and a half metres is the common panel height, often with a topping above it. Height is usually set by the risk assessment rather than by the product range.
Not directly, but corrosion does. A fence that is rusting at the weld intersections loses section over time — specify the coating for the site and the fence keeps its stated wire diameter for its service life.
Send us the run length, the height, the finish and the gate schedule and we will price the panel, post and fixing package.
For the product range see 358 security fence, and for a full specification example see anti-climb 358 mesh panels. If you are comparing systems, our anti-climb fence specification sets out where 358 stops and other systems begin.
Contact Us
Imfornation
Noise Control SolutionsAluminum Alloy Noise Barrier Supplier3m High Noise BarrierIndustrial Plant Noise Barrier: Boundary Wall and Equipment EnclosureNoise Barrier Guide: Types, Height, Cost and Selection3D Curved Fence Panel ManufacturersIndustrial Noise Barrier System129 STC Noise Barrier WholesaleResidential Noise Barrier: Height, Planning and AppearanceAnti-Climb Fence Specification: 358 Mesh, Paladin Pales and 3D PanelsTemporary Fence: Panels, Ballast and Wind Load on Site3D-Welded Mesh fencing systemHospital Noise Barrier: Ward Targets, Height and CleanabilityMetal Noise Barrier Manufacturer0.85 NRC Noise Barrier WholesaleFence Cost Per Metre: What Actually Moves the Price of a Boundary FenceSubstation and Transformer Noise Barriers: Controlling Low-Frequency Hum4 Meter Noise Barrier PanelSolar Noise Barrier Cost: What Drives the Price and the Payback6m High Noise Barrier1115m High Noise BarrierGabion Baskets for saleDouble Wire Fence: 868 and 656 Panels, Posts and FixingsSchool Noise Barrier: Cutting Traffic Noise at the ClassroomRailway and HSR Noise Barriers: Design for Speed and ClearanceGabion Basket SupplierMetro Depot Noise Barrier: Enclosure for Depots and Over-Track Development358 Security Fence: Mesh, Wire and Anti-Climb SpecificationInfrastructure Noise ControlUrban Noise ControlChain Link Fence: Wire, Mesh and Coating SelectionNoise barriers costHighway Noise Barrier Cost: What Drives the Price per Square MetreCooling Tower Noise Barrier: Layout, Airflow and Panel DesignConstruction Site Noise Barriers: Temporary Screens That Move With the WorksConstruction Site Fencing: Temporary Panels, Welded Mesh or Hoarding2m High Noise Barrier