358 Security Fence

358 Mesh Fence Panels: Galvanised or Powder Coated

Two finishes are offered on the same 358 panel, and they do different jobs. This page separates what the zinc does from what the powder coat adds, so the finish is chosen for the site rather than by colour.
  • 358 Mesh Fence Panels: Galvanised or Powder Coated
  • 358 Mesh Fence Panels: Galvanised or Powder Coated
  • 358 Mesh Fence Panels: Galvanised or Powder Coated
  • 358 Mesh Fence Panels: Galvanised or Powder Coated
358 Mesh Fence Panels: Galvanised or Powder Coated
White background product render of a 358 anti-climb mesh panel with folded edges

Two Finishes, Two Different Jobs

Galvanising protects the steel. Powder coating gives the run a colour and a second barrier on top of that protection. They are not alternatives at the same level, and treating them as such is how a coated fence ends up rusting at the joints in its third year.

The zinc is what stops the wire corroding. It does that in two ways: as a barrier over the surface, and by sacrificing itself at a damaged point so the steel beside it does not start to rust. A powder coat cannot do the second job, which is why it is always applied over galvanised wire rather than instead of it.

On a 358 panel the places that matter are the welded intersections and the cut ends, because those are the points a coating is thinnest or absent.

What Hot Dip Galvanising Does

Hot dip galvanising covers the wire inside and out, including the welded joints, because the panel is dipped after welding rather than coated beforehand. That is the difference between a joint that is protected and one that is protected only where the wire surface was.

Zinc thickness is specified by the buyer rather than assumed, because it is the single figure that decides how long the fence lasts in a given atmosphere. A coastal site and an inland industrial site do not need the same figure, and the specification should say which one applies before the order is placed.

Galvanised panels read as bare metal. That is usually the right choice where the fence is industrial, where the budget is tight, or where the client intends to paint later.

Galvanised 358 panels stacked in rows showing the zinc finish

What Powder Coating Adds

Green powder coated 358 panel fixed to a steel post with anti-tamper bolts

Powder coating adds colour and a continuous film over the galvanising. The colour matters more than it sounds: a dark green or black run reads as a boundary rather than a barrier, and it does not glare under floodlights.

The film also absorbs abrasion at the points where the fence is struck, which is where galvanising alone wears through first. On a site with regular contact, that extends the life of the zinc underneath.

The coating is not a repair. Cut ends and any damage during transport still need treatment on site, and a coated panel that is scratched through to bare steel will rust at that point regardless of the colour around it.

Choosing by Site Condition

Match the finish to what the fence is exposed to, not to a catalogue default.

Coastal or marine air, chlorinated surroundings, and heavy industrial atmosphere all shorten the life of any coating system. Those sites justify a heavier galvanised specification first, and a powder coat second.

Where the fence is visible to the public or forms part of a building elevation, colour is usually the deciding factor and the galvanising is specified to suit the exposure.

Where the run will be painted on site later, galvanised only is the practical choice, because powder coat cannot be overpainted reliably.

358 fence run against a building facade showing the finished appearance
Curved run of 358 mesh panels following a site boundary

Where Each Finish Is Used

  • Galvanised only: industrial perimeters, storage yards, sites where appearance is secondary

  • Galvanised and powder coated: boundaries visible to the public, corporate sites, runs adjoining a building

  • Dark colours: boundaries where the fence should recede rather than stand out

  • Light colours: sites where heat gain on the panel matters, or where the client's brand specifies it

Order Details That Change the Price

Close-up of the clamp fixing and post connection on a 358 panel

Three things move the price more than the panel itself: the zinc thickness, whether a powder coat is added, and the post fixing. Send all three with the enquiry.

Also send the run length, the height, gate widths, and the destination port. Supply only outside China; installation is by the client's contractor.